MFM 5100

Particulate Matter Mass Flow Monitor with High Sensitivity

Sensing the electrical field changes induced by the particles motion in gas flow, MFM 5100 can measure the particle flow rate or concentration based on electrical field and flow dynamics models. Extracting particle flow information from electrostatic flow noises with digital signal processing algorithms, MFM 5100 can achieve stable and reliable results with extremely high sensitivity.

Benefits

• Preventive monitoring to reduce equipment maintenance cost

• Management equipment performance in real time, locate problem with no delay

Application

• Particulate matter flow monitoring in low concentration condition, such as after dust collector, for preventive monitoring

Specifications

• Precision: up to 0.01mg/m3

• Range: 0~500mg/m3

• Zero drift:<0.01%FS

• Repetitive Error: < 2%

• Automatic probe contamination check

• Flow media velocity range: 5~35m/s

MFM 6100

Two-Phase Mass Flow Meter

The Correflow MFM combines the technology of two patented measurement techniques (velocity and concentration) in a single sensor to achieve a measurement of mass flow. The first measurement determines the two phase slurry velocity and the second measurement determines the fraction of one of the phases of the mixture in relation to the other. Combining these two parameters yields mass per unit time (ie. mass flow).

• Two Component Concentrations: 1% to 99%

• Materials: Insulating liquids, solids (particulate), gas (bubbles or as carrier)

• Typical Response Time: Concentration–updated at 2.5 millisecond intervals using last measured velocity; Velocity–typically updated once per second

• Purge Option: Type Z purged (NEMA 4X): Cl1, Div 2, GR C&D

• European (Eex approved) housing also available

• Sensor: Typical Sensor Pipe sizes: 1/8” (.32 cm) ID or greater

• Pressure limits: 1000 psi (69 bar) typical for small sensors, Higher pressure designs available. No moving parts, no flow restrictions or additional pressure drop

• Power Requirements: 115 to 240 VAC, 50 to 60 Hz (100 Watts maximum)

• Instrument air for optional pressurization(intermittently 4 scfm @ 80 to 120 psi)

• Data Analysis Velocity, volume fraction, mass fraction, mass flow measurements on an instantaneous basis and averaged over user programmed time intervals, Total mass for fixed time intervals, Stream temperature

• Calibration Routines: Sensor self-tuning with optional dynamic auto-zeroing routines; Adjustable gain on concentration and velocity measurement circuitry; Adjustable signal filtering on concentration measurement circuitry; Adjustable sampling rate for a wide range of process conditions

• Software and fully installed PC available

• Sensor connections designed intrinsically safe

• Each sensor has Four 4-20mA outputs which are independently

• programmable to any Four of 12 available parameters

• MODBUS over RS485 or Ethernet communications: communication or data read out for remote parameter adjustment, calibration and testing.

• Various digital and analog inputs optionally available

Benefits

• Continuous analysis with selectable time averaging

• No moving parts, unaffected by vibration

• No additional pressure drop

• Selectable output scaling

• Designed intrinsically safe

• Ruggedized for the factory environment

• Instantaneous and average mass flow outputs

• Non-contact measurement

Application

• Maintaining maximum reactor productivity is only one of the concerns addressed by the modem-equipped Correflow unit. The rate at which catalyst is delivered to a reaction is also critical in achieving desired mechanical properties. The MFM System also provides early warning for abnormal operation such as clogged feed lines and empty feed pots. Due to the residence time of the catalyst, controllers without the MFM would not have real-time feedback and would have to wait until the reaction slowed before realizing that there was a problem. The MFM6100 enables closed-loop process control to automatically monitor and adjust catalyst flow for maximum reactor efficiency.

MFM 5100

Particulate Matter Mass Flow Monitor with High Sensitivity

Sensing the electrical field changes induced by the particles motion in gas flow, MFM 5100 can measure the particle flow rate or concentration based on electrical field and flow dynamics models. Extracting particle flow information from electrostatic flow noises with digital signal processing algorithms, MFM 5100 can achieve stable and reliable results with extremely high sensitivity.

Benefits

• Preventive monitoring to reduce equipment maintenance cost

• Management equipment performance in real time, locate problem with no delay

Application

• Particulate matter flow monitoring in low concentration condition, such as after dust collector, for preventive monitoring

Specifications

• Precision: up to 0.01mg/m3

• Range: 0~500mg/m3

• Zero drift:<0.01%FS

• Repetitive Error: < 2%

• Automatic probe contamination check

• Flow media velocity range: 5~35m/s

MFM 5200

Particulate Matter Mass Flow Monitor with High Noise Resistance

Sensing the electrical field changes induced by the particles motion in gas flow, MFM 5200 can measure the particle flow rate or concentration based on electrical field and flow dynamics models. Extracting particle flow information from electrostatic flow noises with digital signal processing algorithms, MFM 5200 can achieve stable and reliable results without affected by strong interference, such as ion stream or electric field changes.

MFM 5600

Particulate Matter Mass Flow Monitor with High Dynamic Range

Sensing the electrical field changes induced by the particles motion in gas flow, MFM 5600 can measure the particle flow rate or concentration based on electrical field and flow dynamics models. Extracting particle flow information from electrostatic flow noises with digital signal processing algorithms, MFM 5600 can achieve stable and reliable results under high particle concentration flow condition.

Benefits

§  Monitor equipment load, reduce equipment maintenance cost

§  Measure flow rate under heavy flow conditions, such as pneumatic transport, for stable process operation

§  Prevent blockage

Application

§  Particulate matter flow monitoring in high concentration condition, such pneumatic transport, for stable process operation

Specifications

§  Precision: 1mg/m3

§  Range: 0~100g/m3

§  Zero drift:<0.01%FS

§  Repetitive Error: < 2%

§  Automatic probe contamination check

§  Flow media velocity range: 5~35m/s

MFM 7600