建材可燃性試驗爐是檢測儀器，適用于判定建筑材料是否具有可燃性的試驗方法。使用前務必仔細閱讀說明書。并由 實驗人員操作，以避免操作不當引起的傷害。如需了解更多資料請與我公司客服人員聯系。

The flammability test furnace for building materials is a testing instrument that is suitable for testing methods to determine whether building materials have flammability. Be sure to read the instructions carefully before use. It is operated by experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.

建材可燃性試驗爐適用標準：

GB8626-2007《建筑材料可燃性試驗方法》

GB/T1080L2-2002《熱用擠塑聚苯乙烯泡沫塑料（XPS）》

Applicable standards for building material flammability test furnace:

GB8626-2007 "Test method for flammability of building materials"

GB / T1080L2-2002 "Extruded Polystyrene Foam (XPS) for Thermal Insulation"

建材可燃性試驗爐技術參數：

★箱體高度700×400×600mm

★試樣尺寸250×90mm

★試件A大厚度60mm

★燃燒器噴嘴孔徑φ0.17mm

★外型尺寸：700mm×400mm×810mm

Technical parameters of building material flammability test furnace:

Box height 700 × 400 × 600mm

★ Sample size 250 × 90mm

★ Test piece A large thickness 60mm

★ Burner nozzle aperture φ0.17mm

★ External dimensions: 700mm × 400mm × 810mm

建材可燃性試驗爐特點：

★該裝置的箱體采用不銹鋼板（δ1.5mm）彎彎制而成，其造型美觀、線條清晰，

★具有耐腐蝕抗老化特點。

★該建筑保溫材料燃燒性能檢測裝置裝置中燃燒器配備測量火焰標尺，燃燒器火焰調節方便、靈活、準確。

★試件夾按標準所規定的結構，嚴格制做，試件裝夾，速度快、燃燒效果好

Characteristics of building material flammability test furnace:

★ The box of this device is made of stainless steel plate (δ1.5mm), its shape is beautiful, its lines are clear, and it has the characteristics of corrosion resistance and aging resistance.

★ The burner in this building insulation material combustion performance detection device is equipped with a measuring flame ruler. The burner flame adjustment is convenient, flexible and accurate.

★ The test piece clamp is strictly made according to the structure specified by the standard. The test piece is clamped with fast speed and good combustion effect.

結構及安裝：

★結構

該試驗儀由燃燒試驗箱、燃燒器、試驗支架、調節閥等幾部分組成。液化氣罐自備

★安裝

將底座放入箱體內，固定套、試樣架等按圖示安裝好。將燃燒器放在試樣前。燃燒器拉桿從箱體外箱體內擰在燃燒器底座上。將表與液化氣罐連接上，將調節閥與表的另一端用塑料管連接好，用氣動管將調節閥與燃燒器連接起來。

Structure and installation of flammability test furnace for building materials

★ Structure

The tester consists of a combustion test box, a burner, a test support, and a regulating valve. Own LPG (propane) tank

★ Installation

Put the base into the box, install the fixing sleeve, sample holder, etc. as shown in the figure. Place the burner in front of the sample. The burner rod is screwed onto the burner base from the outside of the box. Connect the propane meter to the liquefied gas tank, connect the regulating valve to the other end of the propane meter with a plastic tube, and connect the regulating valve to the burner with a pneumatic tube.

檢測裝置試驗操作：

★選用合適的點火定位器，放在燃燒器頂端。

★試樣放在試樣夾內，掛上。

★燃燒器接近試樣對好位置后，把底板上直尺鎖緊定位。

★將濾紙放在鋁箔制的收集盤內，放在試件下方。

★將燃燒器立起，打開調壓閥旋鈕，用電子點火器在噴嘴上點火，逐漸調節火焰長度至20mm左右，將燃燒器傾斜45度，按照標準要求的距離給試樣點火

Test operation of building insulation material combustion performance testing device

★ Select a suitable ignition positioner and place it on the top of the burner.

★ Put the sample in the sample holder and hang it up.

★ After the burner approaches the sample alignment position, lock the ruler on the bottom plate to locate it.

★ Put the filter paper in the collection tray made of aluminum foil under the test piece.

★ Stａnd the burner, open the knob of the pressure regulating valve, use the electronic igniter to ignite on the nozzle, gradually adjust the flame length to about 20mm, tilt the burner 45 degrees, and ignite the sample according to the standard distance