頻率范圍可達DC-400MHz，內置6GHz Channel 3
每秒12位的精確測量40ps時間間隔分辨率
的萬用特色
完整的數學運算功能及簡易的操作面板
快速測量及特殊應用
免費的遠端操控軟件及常用的SCPI指令
注意 : 紅色字體為U6220A 沒有提供的功能
12位分辨率 含6GHz頻率測量
本公司根據ISO9004制程所生產出的U6200A通用頻率計數器能夠提供每秒12位數頻率分辨率(見Figure-1)、40 ps時間間隔解析，以及完整的測試與分析功能。另外，本產品還內建第三頻道，可量測頻率從375 MHz到6GHz，而和第二頻道，可量測頻率從1 mHz到 to 400 MHz。
的萬用特色
本產品U6200A也提供了其它不錯的功能及設計，例如：頻率比率(每秒11位)、時間間隔、周期(2.5 ns至1000 s)、 工作周期、脈沖寬度、上升/下降時間、峰值電壓( 100 Hz到300 MHz)、相位、總計、時基溫度變化穩定度(小于1 PPM)、老化率(每年小于2 PPM)、時基參考(I/O見Figure-2)、前端隔離。另外還提供20組設定存儲空間，讓使用者儲存常用的設定(見Figure-3)。
完整的數學運算功能及簡易的操作面板
本產品U6200A內建統計及數學運算功能。使用者可以做一般量測、同步量測、中間值統計、/最小值統計、三角函數統計及標準差統計(見Figure-4)。以及運用Scale & Offset功能按鍵，使用者可依實際應用加入補償值。而要完成以上操作并根據需求輸入數值，使用者只需輕易地利用本產品面板上的數字鍵即可。再者，本公司為了使用者操作方便，將功能按鍵設計成當功能啟用時，按鍵便會亮起(見Figure-5)。
快速測量及特殊應用
本產品U6200A采用即時數字信號進程技術，即可在分析數據之際，同時讀取新值并做快速測量。值得一提的是「限值模式」，使用者可以依需求設定及最小值，并通過面板設定成Go-On或Stop，再開啟USB Output，此時只要測量值超過所設定的范圍， U6200A就會按照設定繼續或停止測量，同時輸出信號觸發外部裝置(見Figure-6)。
免費的遠端操控軟件及常用的SCPI指令
使用者除了可以通過微軟Excel應用軟件(見圖九)，經由內建的USB或選購的GPIB接口取得資料，還可以利用U6200A支持網路伺服器功能，將內建的網絡通信接口連結PC ，并在PC上的瀏覽器中輸入預設的位址192.168.0.247，使用者便可通過網絡操作界面GUI(見Figure 10)操控U6200A。另外，靠著與安捷倫53132A相容的SCPI指令集，U6200A能夠在應用上提供使用者熟悉的語法字串。相關指令集信息，請參照使用U6200A使用手冊第七章節。
U6200A / U6220A 規格表
A.規格表
本附錄包含 U6200A/220A 的規格。 它涵蓋了各種條件下的交流、直流、電阻、溫度和頻率/周期特性。 為方便起見，它還包含一般特性和精度計算。 我們付出了很多努力來確保這些規范滿足您的生產、工程和/或研究需求。 除非另有說明，否則所有規格均適用于 U6200A/220A。
※ 注意：U6220A 不提供綠色規格。
| Channel 1 & 2 (for U6200A only) Input Specifications | ||
| DC Coupled | 1mHz to 400 MHz | |
| AC Coupled | 200KHz to 400 MHz (50 Ω) 30 Hz to 400 MHz (1 MΩ) | |
| FM Tolerance | FM Tolerance: 25% | |
| Voltage Range and Sensitivity | ||
| 1mH to 225 MHz | 20 mVrms to ±5 V ac + dc (Medium and High) 25 mVrms to ±5 V ac + dc (Low) | |
| 225 MHz to 400 MHz | 30 mVrms to ±5 V ac + dc | |
| Channel 1 & 2 (for U6200A only) Input Characteristics | ||
| Impedance (ATT X 1, 1 MΩ Capacitance) (ATT X 10, 1 MΩ Capacitance) | 1 MΩ or 50 Ω 24 pF 15 pF | |
| Coupling | AC or DC | |
| Low-Pass Filter | 100 KHz (or disabled) –20 dB at > 1 MHz | |
| Input Sensitivity | Selectable between Low, Medium(default), or High Medium is approximately 1.35x High Sensitivity, low is approximately 1.7x High Sensitivity | |
| Internal Noise | 200uVrms(typical) | |
|
| ||
| Voltage Range and Sensitivity (Single-Shot Pulse) | ||
| 1.5ns to 10ns Pulse Width | 80 mVpp to 10 Vpp (150 mVpp with optional rear connectors) | |
| >10 ns Pulse Width | 50 mVpp to 10 Vpp (150 mVpp with optional rear connectors) | |
|
| ||
| Trigger Level(ATT x 1) | ||
| Range | ±5.125 V | |
| Accuracy | ±(15 mV + 1% of trigger level) | |
| Resolution | 2.5mV | |
| ATT x 10 Range | X 10 | |
| Trigger Slope | Positive or Negative | |
| Auto Trigger Level | Range | 0 to 99% in 1% steps |
| Frequency | Peak Voltage fast mode >10 KHz Peak Voltage slow mode > 100 Hz Amplitude> 100 mVpp (No amplitude modulation) | |
|
| ||
| Damage Level | ||
| DC~400MHz 50 Ω | 12 Vrms | |
| 0 to 3.5 kHz, 1 MΩ | 350 V dc + ac pk | |
| 3.5 kHz to 100KHz, 1 MΩ | 350 V dc + ac pk linearly derated to 12 Vrms | |
| 100KHz to 400MHz, 1 MΩ | 12 Vrms | |
| Attenuator | ||
| Voltage Range | x10 | |
| Trigger Range | x10 | |
1. 通道 1 和 2 的規格和特性對于通用和獨立配置是相同的。
2. 顯示的值適用于 x 1 衰減器設置。 使用 x 10 衰減器設置時，將所有值乘以 10（標稱值）。 請注意，可能需要在應用環境中（尤其是在高溫下）重新校準輸入偏移，以實現靈敏度。
|
| ||||||||||
| Channel 3 Input Specifications (for U6200A only) | ||||||||||
| Frequency Range | 375 MHz to 6 GHz | |||||||||
| Channel 3 Input Characteristics (for U6200A only) | ||||||||||
| Impedance | 50 Ω | |||||||||
| Coupling | AC | |||||||||
| VSWR | < 2.5:1 | |||||||||
| Power Range and Sensitivity (Sinusoid) | ||||||||||
| 375 MHz to 500 MHz | -16 dBm to +15 dBm | |||||||||
| 500 MHz to 1 GHz | -20 dBm to +15 dBm | |||||||||
| 1 GHz to 2 GHz | -23 dBm to +15 dBm | |||||||||
| 2 GHz to 4 GHz | -25 dBm to +15 dBm | |||||||||
| 4 GHz to 5 GHz | -21dBm to +15 dBm | |||||||||
| 5 GHz to 5.5 GHz | -20 dBm to +15 dBm | |||||||||
| 5.5 GHz to 6 GHz | -17 dBm to +15 dBm | |||||||||
| Damage Level | ||||||||||
| +25 dBm, DC ±12V | ||||||||||
|
| ||||||||||
| External Arm Input Specifications | ||||||||||
| Signal Input Range | LVTTL and TTL compatible | |||||||||
| Timing Restrictions | ||||||||||
| Pulse Width | > 50 ns | |||||||||
| Transition Time | < 250 ns | |||||||||
| Start-to-Stop Time | > 50 ns | |||||||||
| Damage Level | 12 Vrms | |||||||||
| External Arm Input Characteristics | ||||||||||
| Impedance | 1 kΩ | |||||||||
| Input Capacitance | 17 pF | |||||||||
| Start Slope | Positive or Negative | |||||||||
| Stop Slope | Positive or Negative | |||||||||
| Notes | 1. External Arm is available for all measurements except Peak Volts. 2. External Arm is referred to as External Gate for some measurements. | |||||||||
|
| ||||||||||
| Internal Time Base Stability | ||||||||||
|
| Standard (0° to 50°C) | |||||||||
| Temperature Stability (referenced to 25°C) | <± 1 x 10-6 | |||||||||
| Aging Rate | Per Day Per Month Per Year | ± 2 ppm | ||||||||
| Calibration | Electronic | |||||||||
|
| ||||||||||
| External Time Base Input Specifications | ||||||||||
| Voltage Range | 200 mVrms to 10 Vrms | |||||||||
| Damage Level | 12 Vrms | |||||||||
| External Time Base Input Characteristics | ||||||||||
| Threshold | 0 V | |||||||||
| Impedance | 1 kΩ | |||||||||
| Input Capacitance | 25 pF | |||||||||
| Input Frequency | 10 MHz | |||||||||
| Internal vs. External Time Base Selection | Manual | Select Internal or External | ||||||||
| Automatic | Internal used when External not present (default) | |||||||||
| Time Base Output Specifications | ||||||||||
| Output Frequency | 10 MHz | |||||||||
| Voltage | 570 mVpp (0 dBm), typical | |||||||||
| Impedance | 50 Ω (typical), AC coupled | |||||||||
|
| ||||||||||
| Measurement Specifications | ||||||||||
| Frequency, Period Channel 1 and 2 | 1 mHz to 400 MHz (2.5 ns to 1000 s) | |||||||||
| Trigger | Default setting is Auto Trigger at 50 % | |||||||||
| “Default” Gate Time | 0.1 sec | |||||||||
| STD CH 3 | 375 MHz to 6 GHz (0.166 ns to 2.6 ns) | |||||||||
| Frequency Ratio | CH 1/ CH 2, CH 1/ CH 3, CH 2/ CH 1, CH 3/ CH1 | |||||||||
| (Measurement is specified over the full signal range of each input.) | ||||||||||
| Results Range | 10-10 to 1011 | |||||||||
| “Default” Gate Time | 0.1 sec | |||||||||
| Time Interval | Measurement is specified over the full signal ranges of Channels 1 and 2. The width of the pulse must be greater than 1 ns, frequency range to 300 MHz. | |||||||||
| Trigger | Default setting is Auto Trigger at 50 % | |||||||||
| Results Range | -0.5 ns to 105 s | |||||||||
| Resolution | 40 ps | |||||||||
| RMS Resolution | 120 ps | |||||||||
| Systematic Uncertainty | ±(TI × Time Base Error) ± Trigger Level Timing Error ± 500 ps Differential Channel Error | |||||||||
| Pulse Width Time | Measurement is specified over the full signal range of Channel 1. The width of the pulse must be greater than 1 ns frequency range to 300 MHz). | |||||||||
| Pulse Selection | Positive or Negative | |||||||||
| Trigger | Default setting is Auto Trigger at 50% | |||||||||
| Results Range | 1.5 ns to 105 s | |||||||||
| Resolution | 40 ps | |||||||||
| RMS Resolution | 120 ps | |||||||||
| Systematic Uncertainty | ± (Pulse Width Time x Time Base Error) ± Trigger Level Timing Error ± 500 ps Differential Channel Error. | |||||||||
| Rise/Fall Time | Measurement is specified over the full signal range of Channel 1. The width of the pulse must be greater than 1 ns frequency range to 300 MHz). | |||||||||
| Edge Selection | Positive or Negative | |||||||||
| Trigger | Default setting is Auto Trigger at 10% and 90% | |||||||||
| Results Range | 2 ns to 105 s | |||||||||
| Resolution | 40 ps | |||||||||
| RMS Resolution | 120 ps | |||||||||
| Systematic Uncertainty | ± (Edge Time x Time Base Error) ± Trigger Level Timing Error ± 500 ps Differential Channel Error | |||||||||
| Phase | Measurement is specified over the full signal range of each input. The width of the pulse must be greater than 1 ns, frequency range to 300 MHz | |||||||||
| Results Range | -180° to +360° | |||||||||
| Resolution | 40 ps | |||||||||
| RMS Resolution | 120 ps | |||||||||
| Systematic Uncertainty | ± (Trigger Level Timing Error) ×Frequency | |||||||||
| Duty Cycle | Measurement is specified over the full signal range of Channel 1. The width of the pulse must be greater than 1 ns, frequency range to 300 MHz | |||||||||
| Pulse Selection | Positive or Negative | |||||||||
| Trigger | Default setting is Auto Trigger at 50 % | |||||||||
| Results Range | 0 to 1 | |||||||||
| Resolution | 40 ps | |||||||||
| RMS Resolution | 120 ps | |||||||||
| SystematicUncertainty | ± Trigger Level Timing Error ± 500 ps Differential Channel Error | |||||||||
| Totalize | Measurement is specified over the full signal range of Channel 1. The width of the pulse must be greater than 1 ns, frequency range to 400 MHz | |||||||||
| Pulse Selection | Positive or Negative | |||||||||
| Trigger | Default setting is Trigger at 0 V | |||||||||
| Results Range | 0 to 1015 | |||||||||
| Resolution | 1 count | |||||||||
| Systematic Uncertainty | ± 1 count | |||||||||
| Peak Voltage | Results Range | -5.1 V to + 5.1 V | ||||||||
| Resolution | 2.5 mV | |||||||||
| DC Signals |
| 15 mV + 2 % of V | peak-to-peak amplitude greater than 200 mV | |||||||
| DC Signals (ATT x 10) |
| 150 mV + 2 % of V | peak-to-peak amplitude greater than 1 V | |||||||
| 1 Vp-p, 50 Ω, ATT OFF | 100 Hz ~ 10 KHz | 15 mV + 2 % of V | peak-to-peak amplitude greater than 200 mV | |||||||
| 10 KHz ~ 5 MHz | 15 mV + 4 % of V | |||||||||
| 5 MHz ~ 80 MHz | 15 mV + 7 % of V | |||||||||
| 80 MHz ~ 300 MHz | 15 mV + 15 % of V | |||||||||
|
| ||||||||||
| Rear Input Option Channel Isolation | ||||||||||
| Frequency | Front Channel(dB) | Rear Channel(dB) | ||||||||
| 100KHz | <-85 | <-85 | ||||||||
| 1MHz | -85 | -75 | ||||||||
| 10MHz | -78 | -55 | ||||||||
| 50MHz | -67 | -42 | ||||||||
| 100MHz | -62 | -37 | ||||||||
| 200MHz | -55 | -35 | ||||||||
| 300MHz | -50 | -36 | ||||||||
| 400MHz | -47 | -33 | ||||||||
盡管結果僅用作參考，但峰值電壓測量將繼續運行至 400 MHz。
許多系統不確定性方程計算的差分通道誤差項會導致通道間不一致和內部噪聲。 這些問題可以通過 TI 校準在良好控制的溫度環境中得到改善。
A.1 RMS Resolution
| Rms | 100Hz | 1KHz | 10KHz | 100KHz |
| U62 (10ms) | 0.000000842 | 0.000003438 | 0.000013896 | 0.000067275 |
| U62 (100ms) | 0.0000001 | 0.000000828 | 0.000005093 | 0.000011508 |
| U62 (1s) | 0.000000001 | 0.000000098 | 0.000001212 | 0.000004869 |
| Rms | 1MHz | 10MHz | 100MHz | 1GHz |
| U62 (10ms) | 0.000677504 | 0.004830870 | 0.042107484 | 0.611551072 |
| U62 (100ms) | 0.000101040 | 0.002272900 | 0.006344503 | 0.055991810 |
| U62 (1s) | 0.000058166 | 0.000469601 | 0.001275299 | 0.002602258 |
該圖不包括觸發錯誤的影響。 為了給這個誤差項的附加效應設置一個上限，有必要從正確的圖表中確定頻率誤差并添加一個觸發誤差項，如下等式：
外部源和輸入放大器噪聲可能會提前或推遲定義測量開始和結束的觸發點。 由此產生的時序不確定性是信號壓擺率和寄生噪聲尖峰幅度（相對于輸入遲滯帶）的函數。
相對于單個觸發點的 (rms) 觸發誤差為：
B. 預設值和保存/調用信息
※ 注意：U6220A 不提供綠色通道 2 的功能。|
| Value at *RST | In Save/Recal | In non-volatile memory | |
| Input impedance | CH1 | 1E+6Ohms | yes | no |
| CH2 | 1E+6Ohms | yes | no | |
| Input Attenuation | CH1 | ×1 | yes | no |
| CH2 | ×1 | yes | no | |
| Trigger Level | CH1 (percent) | 50 | yes | no |
| CH2 (percent) | 50 | yes | no | |
| CH1 (volts) | 0 | yes | no | |
| CH2 (volts) | 0 | yes | no | |
| Trigger Slope | CH1 | positive | yes | no |
| CH2 | positive | yes | no | |
| Sensitivity | CH1 | Medium | yes | no |
| CH2 | Medium | yes | no | |
| Scale | 1 | yes | no | |
| Offset | 0 | yes | no | |
| Limits parameters | Limit test on/off | off | yes | no |
| On fail stop/go on | go on | yes | no | |
| Lower limit | 0 | yes | no | |
| Upper Limit | 0 | yes | no | |
| Stats parameters | Stats on/off | off | yes | no |
| Measurement count | 100 | yes | no | |
| Display measurement/stats | measurement | yes | no | |
| Use all/in limits | all | yes | no | |
| On-single measurement | 1 | yes | no | |
| Timebase | auto | yes | no | |
| Trigger Offset Cal Parameters | Channel 1 trigger offset Inp1 cal | no | yes | |
| Channel 2 trigger offset Inp2 cal | no | yes | ||
| Channel 1 trigger offset Att1 cal | no | yes | ||
| Channel 2 trigger offset Att2 cal | no | yes | ||
| Trigger Gain Cal Parameters | Channel 1 trigger gain Inp1 cal | no | yes | |
| Channel 2 trigger gain Inp2 cal | no | yes | ||
| Channel 1 trigger gain Att1 cal | no | yes | ||
| Channel 2 trigger gain Att2 cal | no | yes | ||
| Time Interval Offset Cal Parameters | Fine1 | no | yes | |
| Fine2 | no | yes | ||
| Quick | no | yes | ||
| Timebase cal Parameters | no | yes | ||
C. 一般規格
※ 注意：U6220A 不支持項目 1 ~ 4 中的綠色配件。
| Item | Limitation & description |
| Power Supply Voltage | 100V/240V ± 10% 50Hz~60Hz ± 10% |
| 100V/120V ± 10% 400Hz ± 10% | |
| Power Requirements | Max. 80VA (30W Typtical) |
| Operating Humidity | Maximum relative humidity 80% for temperature up to 31 ℃ decreasing linearly to 50% relative humidity at 40℃ |
| Operating Environment | 0 to 55 ℃ |
| Storage Temperature | - 40 ℃ to 70 ℃ |
| Operating Altitude | Up to 2000m |
| Dimensions for Rack (WxHxD) | 214.6 x 88.6 x 346.9 mm |
| Weight | 3130 g / 2887 g |
| Safety | IEC61010-1:2010/EN61010-1:2010 (3rd Edition) |
| IEC61010-2-030:2010(1st Edition)/ | |
| EN61010-2-030:2010 | |
| EMC | EN61326, IEC61000-3, IEC61000-4 |
| Warm-up Time | 1 Hour |
| Warranty | 1 Year |
| Accessory | 1. U6200-opt04: Rear panel input module (CH1/CH2) 2. U6200-opt05: Rear panel input module (CH1/CH2/CH3) 3. M3500-opt04: GPIB Card |
※注1：配件必須在Picotest中組裝。
※注意2：不要將設備放置在難以操作斷開裝置的位置。
※ 注意 3：文件中應指示不要用額定值不足的電源線更換可拆卸的電源線。
U6200-OPT04 : Rear Input (CH1/2)模組
U6200-OPT05 : Rear panel input (CH1/2/3)模組
M3500-OPT04 : GPIB卡
衡水市|
乐业县|
鄂托克前旗|
福贡县|
太谷县|
滁州市|
新泰市|
焦作市|
河池市|
红河县|
八宿县|
望谟县|
灵川县|
峨眉山市|
金昌市|
马龙县|
习水县|
绥阳县|
盘锦市|
灯塔市|
定安县|
郓城县|
丽水市|
SHOW|
陈巴尔虎旗|
东丽区|
延长县|
社会|
金乡县|
哈密市|
福建省|
越西县|
惠东县|
开封市|
大港区|
嵊州市|
夏津县|
阳东县|
增城市|
珲春市|
池州市|