| Management of electric screw driver |
| ●Torque Meter CD-100M/10M |
| upgrade The main changed parts (1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display. (2) Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc. (3) Setup of Various Numerical Values Can be EasyCan Carry Out Speedily. (4) Calculation of Maximum, Minimum,Average Became Inligible. (5) The call of the saved data became easy. The output of data also became inligible. (6) Fault charge protection. It is pilot-lamp lighting during charge. (7) Data Output is USB Form (B Type). (8) Memory Data are 800 Affairs (9) Real-time Output is Every 1 / 180 Seconds. |
| Specification | CD-100M | CD-10M | ||
| Measuring range (at the time of Track) | 0.10~10 N・m | 1.0~100?。鉔・m | ||
| 1.0~100 kgf・cm | 0.10~10 kgf・cm | |||
| 1.0~90 lbf・in | 0.10~9 lbf・in | |||
| Accuracy | ±0.5%(F/S)(199 or less digit±1digit) | |||
| Display | The 3.5 figures digital display of LCD | |||
| The measurement direction | CW-CCW (rightleft) | |||
| Measurement Mode | Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output) | |||
| Highlow limits judging function | Highlow value are measurement within the limits,can be set up. | |||
| Real-time Output | Load torque value is outputted every about1/ 180 second. | |||
| The Maximum, the minimum,the average value display | The maximum, the minimum, average value,the data number of 30 data are displayed.It saves to ten channels. | |||
| Automatic Clearance | Automatically clear the displayed value after certain time (0.5 - 3.0 sec,selectable at each 0.5 sec). Setting 0.0 sec for manual Zero clearance | |||
| One-touch zero | A clear button is pushedit is a zero. Data is outputed. | |||
| Data output | ASCII format (baud rate 19200) | |||
| Power supply | Ni-Cd chargeable battery 1.2V×5cells 700mAh | |||
| Auto power save | 10 minutes no use, automatically switch off. | |||
| Charging time | About 3 hours | |||
| Continunous working time | About 12 hours | |||
| Socket fit mouth | □ 20mm/ □9.5mm | |||
| Weight | Abbreviation 1 kg | |||
| Outside dimension | 160(W)×125(D)×55(H) | |||
| Attachment | Measurement joint SJ50/SJ10K | Measurement joint SJ10 | ||
| Accessories | AC/DC adaptor | |||
| Exclusive receipt case | ||||
| An inspection report, a proofreading certificate, traceability system figure | ||||
| SJ50 | SJ10 | About an adapter <measurement joint SJ(PAT.P)> |
| It does not decompose, even if it rewinds joint too much Since the adapter attached is the coil spring compression system of the conventional system, you can use it by the conventional management method. Moreover, this adapter is special structure. It does not decompose, even if it rewinds joint too much. You can use it in comfort. |





































商南县|
皋兰县|
桦南县|
景宁|
利津县|
大宁县|
望奎县|
富顺县|
江达县|
崇左市|
普安县|
合山市|
长泰县|
白城市|
阿巴嘎旗|
紫金县|
寻乌县|
靖宇县|
措勤县|
鹤岗市|
西盟|
隆子县|
仁化县|
定州市|
丰都县|
大余县|
镇雄县|
彭泽县|
印江|
天峨县|
淮安市|
白玉县|
大兴区|
博白县|
文水县|
进贤县|
工布江达县|
囊谦县|
建阳市|
南澳县|
宜宾县|