MLV-8T/MLV-8T速度傳感器

MLV-8Vibration Velocity Sensor

1．概述

MLV-8T/MLV-8T速度傳感器主要安裝在各種旋轉機械裝置的軸承蓋上（如汽輪機、壓縮機、風機和泵等）。它是由運動線圈切割磁力線而輸出電壓的電磁式傳感器，因此具有工作時不需要供給電源、安裝容易等特點。

1. Overview

The PR-1020 vibration sensor is mainly installed on the bearing housings of various rotating machinery (such as steam turbines, compressors, fans, pumps, etc.). As an electromagnetic sensor that outputs voltage by moving coils cutting magnetic lines, it features no external power supply required for operation and easy installation.When connected with a vibration severity monitor, it can measure various parameters such as displacement and velocity.

2．技術參數

2．1 靈 敏 度: 50mv/mm/s

2. 2 頻率響應：10 ～ 1000 Hz ，5 ～ 1000 Hz (特制）    

2. 3 誤 差: 10- 300HZ < 2%

          300- 1000HZ < 4%

2．4 自振頻率：10Hz

2．5 可測振幅：≤2mm(P — P)

2．6 最大加速度：10g

2．7 測量方向：水平或垂直

2．8使用環境： -40℃～100℃ 相對濕度 ≤90%

2．9 外形尺寸：φ33×75mm

2．10 重 量: 約300g

2.11 安裝螺釘：M10*1.5

2. Technical Parameters

2.1 Sensitivity: 50 mV/mm/s

2.2 Frequency Response: 10 ~ 1000 Hz; 5 ~ 1000 Hz (custom version)

2.3 Error: < 2% at 10–300 Hz; < 4% at 300–1000 Hz

2.4 Natural Frequency: 10 Hz

2.5 Measurable Amplitude: ≤ 2 mm (P–P)

2.6 Maximum Acceleration: 10 g

2.7 Measuring Direction: Horizontal or vertical

2.8 Operating Environment: -40 ℃ ~ 100 ℃, relative humidity ≤ 90%

2.9 Dimensions: φ33 × 75 mm

2.10 Weight: Approx. 300 g

2.11 Mounting Screw: M10 × 1.5

Two brown and blue wires are signal positive (+); one black wire is the shielding wire.Figure 1 Outline Drawing

3．安 裝

3．1 安裝位置：垂直或者水平安裝于被測振動點上，以變送器底部M8×1.25螺釘磁座吸附在被測殼體上，然后將傳感器擰在上面擰緊即可.

3. Installation

3.1 Mounting Position: Install vertically or horizontally at the measured vibration point. Attach the magnetic base with M8 × 1.25 screw at the bottom of the transmitter to the measured housing, then screw the sensor onto it and tighten.

4.注意事項：傳感器不能外力重?fù)?

4. Notes

Do not strike or impact the sensor with external force.