當前位置：深圳市漢潤電子有限公司>>二手產品 PRODUCTS>>儀器選配件>>交直流電流探頭

交直流電流探頭

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號TCP0150

品牌

廠商性質經銷商

所在地深圳市

在線詢價 收藏產品

聯系方式：袁俊昕查看聯系方式

更新時間：2023-06-22 07:48:04瀏覽次數：83次

聯系我時，請告知來自儀表網

產品分類 品牌分類

  二手產品 PRODUCTS

儀器選配件

信號發生器

頻譜分析儀

網絡分析儀

全部產品列表

暫無信息

深圳市漢潤電子有限公司

經營模式：經銷商

商鋪產品：795條

所在地區：廣東

聯系人：袁俊昕（主管）

詢價 給他留言

產品簡介

產品特點*容易進行高精度AC/DC電流測量，操作簡便，直流電流精度典型值≤1%；*帶寬DC~20MHz，電流從±5mA到150A有效值，可滿足大電流和小電流測試需要；*具有自動匹配刻度單元，并在示波器顯示屏上讀出；*在ATE設備通過GPIB接口可進行遠程編程；*容易退磁和自動歸零

詳細介紹

產品特點

* 容易進行高精度AC/DC電流測量，操作簡便，直流電流精度典型值≤1%；
* 帶寬DC~20MHz，電流從±5mA到150A有效值，可滿足大電流和小電流測試需要；
* 具有自動匹配刻度單元，并在示波器顯示屏上讀出；
* 在ATE設備通過GPIB接口可進行遠程編程；
* 容易退磁和自動歸零。
* 適用示波器型號：DPO4032、DPO4034、DPO4054、DPO4104
* MSO4032、MSO4034、MSO4054、MSO4104
* 部分DPO7000系列示波器。

Features & Benefits

Easy to Use and Accurate AC/DC Current Measurements
Connects Directly to DPO4000, MSO4000 and DPO7000 Series Oscilloscopes Using the TekVPI Probe Interface
DC to 20 MHz Bandwidth
150 A RMS Maximum Current Capability
500 A Peak Pulse Current Capability
High Accuracy with Typically Less than 1% DC Gain Error
Accurately Measures Current levels as low as 5 mA
Low Noise and DC Drift
Provides Automatic Units Scaling and Readout on the Oscilloscope's Display
Remote Programmable GPIB Control for ATE systems
Split-Core Probe Head Construction Allows Easy Connection to Conductors
Easy to Degauss and Autozero
Setup Controls and Probe Status and Diagnostic Indicators are Provided on Both the Probe Hardware and via an Easy-to-Access Scope UI Display Menu

Applications

Power Supplies
Semiconductor Devices
Power Inverters/Converters
Electronic Ballasts
Industrial/Consumer Electronics
Motor Drives
Transportation Systems

Note: Requires DPO7000Series Firmware Version 3.0.2 or greater. Requires DPO4000/MSO4000 Firmware Version 2.06 or greater.

TCP0150 is a high performance and easy-to-use 150 A AC/DC current probe designed for use and direct connection (without the need of an additional power supply) to the TekVPI™ probe interface used on Tektronix DPO4000, MSO4000 and DPO7000 Series oscilloscopes. This AC/DC current measurement probe provides 20 MHz of frequency bandwidth with selectable range control for 25 A and 150 A measurement ranges. It also provides low current measurement capability and accuracy to current levels as low as 5 mA per division — important for achieving broad dynamic current range of high-level and low-level measurement signals.

Characteristics

Warranted

Bandwidth	DC to ≥20 MHz (-3dB). Derate with Frequency. See Figure 1. (Calculated from Rise Time BW = .35/Rise Time)
Rise Time	≤17.5 ns
Max RMS Current	150 A
Max Peak Pulse Current	500 A
Minimum Sensitivity	5 mA (on oscilloscope’s 1 mV/div setting) AC Coupling (on oscilloscopes that support AC/DC coupling)
Current Ranges	25 A and 150 A
Max Bare Wire Voltage	600 V_RMS CAT I & II 300 V_RMS CAT III

Typical

DC Accuracy	±1% Typical 3% Warranted
Max Amp-Second Product
25 A Range	3,000 AµS
150 A Range	15,000 AµS
Insertion Impedance	0.03 Ω @ 1 MHz
	0.075 Ω @ 5 MHz
	.125 @ 10 MHz
	.3 @ 20 MHz
Signal Delay	? 21 ns
Displayed RMS Noise	≤500 μA_RMS (probe only)

Environmental

Temperature
Operating	0ºC to +50ºC
Non-operating	-40ºC to +75ºC
Humidity
Operating	5% to 95% RH (Relative Humidity) at up to +30ºC 5% to 85% RH above 30ºC up to +50ºC, non-condensing
Non-operating	5% to 95% RH (Relative Humidity) at up to +30ºC 5% to 85% RH above 30ºC up to +75ºC, non-condensing
Altitude
Operating	Up to 2,000 meters (6,560 feet)
Non-operating	Up to 12,000 meters (40,000 feet)

Physical Characteristics

	kg	lbs
Shipping Weight	.7865	1.734
Dimensions	meters	inches
Cable Length	2 meters	79 inches
Probe head size
Length	26.8 cm	10.55 in.
Width	4.1 cm	1.6 in.
Height	15.6 cm	6.13 in.
Max Conductor Diameter	21 mm x 25 mm	0.83 in. x 1.0 in.
Power Requirements	TCP0150 is powered directly by the DPO4000, MSO4000 and DPO7000 Series oscilloscopes using TekVPI interface

Recommended Oscilloscopes

DPO4000, MSO4000, and DPO7000 Series oscilloscopes with TekVPI probe interface.

Note: Requires DPO7000Series Firmware Version 3.0.2 or greater. Requires DPO4000/MSO4000 Firmware Version 2.06 or greater.
AC/DC Current Probe with TekVPI Interface.

Includes: Protective Cover (016-1924-xx), and Certificate of Traceable Calibration and Data Standard.

Option	Order
Option L0	Standard English Language Instruction Manual (071-xxxx-xx)
Option L5	Substitutes Japanese Language Instruction Manual
Option L7	Substitutes Simplified Chinese Language Instruction Manual

Recommended Accessories

Accessory	Order
Current Loop, 1 Turn, 50 Ω with BNC connector used for Performance Verification	015-0601-50
TekVPI Calibration Fixture	067-1701-xx
Cal/Deskew Fixture for DPO7000/70000 Series	067-1686-xx

Service Options

Option	Description
Opt. CA1	Provides coverage for a single Calibration Event
Opt. C3	Calibration Service 3 years
Opt. C5	Calibration Service 5 years
Opt. D3	Calibration Data Report 3 Years (with Opt. C3)
Opt. D5	Calibration Data Report 5 Years (with Opt. C5)
Opt. R3	Repair Service 3 Years
Opt. R5	Repair Service 5 Years