PRHD4505型軟化點測定儀
軟化點測定儀根據溫度和機器配置可分四種：
測溫范圍：室溫-99.9℃，不配打印機；
測溫范圍：室溫-180℃，不配打印機；
測溫范圍：室溫-99.9℃，配熱敏打印機；
測溫范圍：室溫-180℃，配熱敏打印機；
該儀器采用了高精度進口溫度傳感器，具有測量溫度精準，每分鐘溫度上升速度在5±0.3℃，符合瀝青規范中規定的5±0.5℃。機器采用大屏幕液晶顯示，操作簡單明了，大氣。軟化點測定儀采用紅外線對光，避免了陽光的干擾，不會產生誤判。機器每分鐘都會自動記錄溫度數據，減少了實驗員的人工記錄，深受用戶的喜歡！歡迎各界人士前來咨詢和探討！
技術參數：
1.電源電壓：AC220V，50HZ；
2.測溫范圍：
⑴試樣軟化點在80℃以下者，用蒸餾水做加熱介質， 5 ℃～ 80℃；
⑵試樣軟化點在80℃以上者，用甘油做加熱介質， 32℃～ 160℃；
3.溫度分辨率：0.1℃；
4.攪拌器：攪拌速度在0-250r/min之間連續可調；
5.加熱速率：三分鐘后自動調整為5.0±0.5℃/min；
6.軟化點結果：液晶顯示，選配打印機打印數據輸出；
7.加熱功率：600W；
8.計算機接口：RS232接口；
9.燒杯容積：800mL；
10.環境條件：環境溫度小于35℃，無空氣對流現象；
11.相對濕度：≤85％；
12.整機功率：700W。 PRHD4505 type Softening Point Tester
Softening Point Tester configuration can be divided into four kinds according to the temperature and the machine:
Temperature range: room temperature -99.9 ℃, unworthy of the printer;
Temperature range: room temperature -180 ℃, unworthy of the printer;
Temperature range: room temperature -99.9 ℃, with thermal printer;
Temperature range: room temperature -180 ℃, with thermal printer;
The instrument uses imported high-precision temperature sensor with accurate temperature measurements per minute rate of temperature rise at 5 ± 0.3 ℃, in full compliance with the provisions of the asphalt specification 5 ± 0.5 ℃. The machine uses large-screen LCD, simple operation, high-end atmosphere. Softening Point Tester uses infrared light to avoid sun interference will not produce false positives. Every minute the machine will automatically record temperature data, reduce the manual recording laboratory assistant, by the users favorite! All are welcome to come to consult and discuss!
Technical Parameters:
1. Power supply voltage: AC220V, 50HZ;
2. Temperature range:
⑴ sample softening point below 80 ℃ by using distilled water as the heating medium, 5 ℃ ~ 80 ℃;
⑵ sample softening point above 80 ℃ by using glycerin as heating medium, 32 ℃ ~ 160 ℃;
3. Temperature Resolution: 0.1 ℃;
4. Stirrer: the stirring speed continuously adjustable between 0-250r / min;
5. Heating rate: three minutes is automatically adjusted to 5.0 ± 0.5 ℃ / min;
6. Results softening point: liquid crystal display, an optional printer data output;
7. Heating power: 600W;
8. Computer Interface: RS232 interfaces;
9. beaker volume: 800mL;
10. Environmental conditions: ambient temperature less than 35 ℃, no air convection;
11. Relative humidity: ≤85%;
12. Total power: 700W.
會員1.png)
灌云县|
SHOW|
南雄市|
武邑县|
阳东县|
英德市|
夏邑县|
扎赉特旗|
罗田县|
措勤县|
荥阳市|
凤冈县|
罗定市|
济源市|
万全县|
康保县|
彰化市|
沾化县|
宁德市|
蚌埠市|
承德市|
汝州市|
怀安县|
绩溪县|
靖州|
万源市|
丰台区|
满洲里市|
塔城市|
英山县|
酒泉市|
外汇|
长岛县|
中江县|
沧源|
谷城县|
科尔|
军事|
凤城市|
辽源市|
磴口县|