當前位置：上海榮計達實驗儀器有限公司>>>>榮計達YZF-2水泥安定性壓蒸釜

榮計達YZF-2水泥安定性壓蒸釜

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號

品牌

廠商性質生產商

所在地

在線詢價 收藏產品

聯系方式：王林查看聯系方式

更新時間：2021-07-21 09:14:05瀏覽次數：108次

聯系我時，請告知來自儀表網

產品分類 品牌分類

  分類
  電子儀表

試驗機

暫無信息

上海榮計達實驗儀器有限公司

經營模式：生產廠家

商鋪產品：1334條

所在地區：上海上海市

聯系人：王林

詢價 給他留言

產品簡介

一、產品簡介：水泥安定性壓蒸釜是依據標準GB/T750-1992《水泥壓蒸安定性試驗方法》對試驗設備的要求而研制的產品

詳細介紹

一、產品簡介：

水泥安定性壓蒸釜是依據 標準 GB/T750-1992《水泥壓蒸安定性試驗方法》對 試驗設備的要求而研制的產品。該水泥安定性壓蒸釜適用于測定硅酸鹽水泥、普通硅酸鹽水泥、礦渣硅酸鹽水泥、火山灰質硅酸鹽水泥、粉煤灰硅酸鹽水泥等主要因方鎂石水化可能造成的水泥體積不均勻變化。

I. Product Introduction

Cement stability autoclave is a product developed in accordance with the requirements of the test equipment in accordance with the standard GB / T750-1992 "Cement autoclave stability test method". The cement stability autoclave is suitable for the determination of portlａnd cement, ordinary portlａnd cement, slag portlａnd cement, pozzolanic portlａnd cement, fly ash portlａnd cement, etc. May cause uneven changes in cement volume.

二、主要技術參數：

★釜體容積：8.5L

★釜體內徑：Φ160mm

★A高工作壓力：2.5Mpa（可人工調整）可控升溫升壓速度

★標準升壓時間(0-2±0.05Mpa；常溫-215.7±1.3℃)：≈45min

★安全閥開啟壓力：3.0Mpa

★壓力自動控制的波動范圍：≯±0.05Mpa

★保壓時間設定范圍：1~99h

★額定電壓：220V

★額定功率：1200+600W

★外形尺寸：1000*660*1320mm

★重量：約75kg

Second, the main technical parameters

★ Volume of kettle: 8.5L

★ Inner diameter of kettle: Φ160mm

★ A high working pressure: 2.5Mpa (can be adjusted manually) Controllable heating and boosting speed

★ Standard boost time (0-2 ± 0.05Mpa; room temperature -215.7 ± 1.3 ℃): ≈45min

★ Safety valve opening pressure: 3.0Mpa

★ The fluctuation range of automatic pressure control: ≯ ± 0.05Mpa

★ Setting time of holding time: 1 ~ 99h

★ Rated voltage: 220V

★ Rated power: 1200 + 600W

★ Dimensions: 1000 * 660 * 1320mm

★ Weight: about 75kg

三、原理：

主要零部件多采用優質不銹鋼材料制造，能耐高溫、高壓飽和水蒸氣。釜蓋上裝有一個由不銹鋼制成的壓力指示表、一個安全閥、二個放氣閥。釜體安裝在筒殼內，其外側下部裝有兩個加熱電阻，用于向釜體加熱，制造水蒸氣；底部道管與電接點壓力表相連，電接點壓力表與電器控制系統配合，用于將釜內壓力控制在設定范圍。筒殼的上部設有通風環，下部設有通風盤，用于阻斷或開通釜體周圍的空氣，在下部安裝有排風扇，用于結束試驗后的排風降溫。控制箱面板設有電源總開關，啟動、停止、風機三個鍵和運行、加熱、風機、停止四個指示信號燈，以及用于計時的數顯時間繼電器。

Three principles

The main parts are mostly made of high-quality stainless steel, which can withstａnd high temperature and high pressure saturated water vapor. The lid of the kettle is equipped with a pressure indicator made of stainless steel, a safety valve and two air release valves. The kettle body is installed in the shell, and two heating resistors are installed on the outer lower part for heating the kettle body to produce water vapor. The bottom tube is connected with the electric contact pressure gauge, and the electric contact pressure gauge cooperates with the electrical control system. In order to control the pressure in the kettle within a set range. The upper part of the shell is provided with a ventilation ring, and the lower part is provided with a ventilation plate for blocking or opening the air around the kettle body. An exhaust fan is installed at the lower part for exhausting and cooling after the test. The control box panel is provided with a main power switch, three keys for start, stop, and fan, and four indicator lights for running, heating, fan, and stop, and a digital display time relay for timing.

四、安裝步驟：

★應安裝在比較僻靜的地方，為保證安全及使用維護方便，應背向墻壁，離墻不少于 500mm，并調整水平，將其固定在地基上。

★用不小于 1.5mm2 的軟銅線將可靠接地。

★連接好控制箱與釜體間的航空插頭。

五，水泥壓蒸釜操作規程：

★ 打開釜蓋，按釜體容積 8.5L 的 7%~10%的注水量，即 595cc~850cc 蒸餾水注入釜內。（通常建議注水量：700 毫升~800 毫升）

★將裝有試件的支架放入內。

★用棉紗將釜口和釜蓋的密封面擦干凈，再用毛筆在釜口密封面上薄薄涂上一層干凈的機油。

★輕輕蓋上釜蓋，下壓并左右轉動釜蓋，確認結合部已正確密合。將 10 個螺母用手?jǐn)Q上。再用扭力扳手按照 50、100、100Nm，分三次按對角線的順序均勻地?cái)Q緊螺母，安裝好釜蓋。

★向釜蓋中的溫度計插管內注入 3~5 滴機油（一般以油面不高于溫度計* 球?yàn)橐耍?，將 300℃*溫度計輕輕插入管內。

★打開兩個放氣閥中的任意一個。

★將電接點壓力表的紅色上限指針調至 2.025MPa 處（即： 2MPa 再上調半格）；將綠色下限指針調至 1.975MPa 處。

★關閉通風盤和通風環。

★接通電源，打開控制箱上的電源總開關，按啟動鍵，運行、加熱指示燈亮，釜體開始以 1800W 功率加熱。同時數顯時間繼電器開始顯示。

★ 當已打開的一個放氣閥有水蒸氣排出時，說明內空氣已經排凈，關閉該放氣閥。閥門關閉后，壓力將隨著溫度的升高而升高此時應注意，儀器工作有無異常，如有異常，則必須查明原因，或按停止鍵停止試驗。

★停止加熱后，風機自動工作，信號燈亮，打開通風盤和通風環，通風環處會 有熱空氣排出，釜內壓力將在 90min 以內降至 0.1MPa 以下。此時可打開放氣閥將釜內 余壓放凈。請不要關閉放氣閥，因冷卻后會造成釜內負壓，而損壞壓力表。

★ 待冷卻至常溫后，按停止鍵，信號燈滅、排風扇停，關閉電源總開關，取下溫度計，以安裝釜蓋相同的方法擰下 10 個拴緊螺母（擰松螺母時至少要用兩個循環，以免損壞密封結合面），取下釜蓋，取出試件支架。用膠管或毛巾將釜內蒸餾水析出擦凈。

★中途停止試驗程序：按“停止"鍵，打開通風盤、通風環，按“風機"鍵，待儀器冷卻后重新安裝試驗。

Fourth, the installation steps;

★ It should be installed in a relatively quiet place. In order to ensure safety and convenient use and maintenance, it should be facing away from the wall, not less than 500mm away from the wall, and adjust the level to fix it on the foundation. Zh

★ Use a flexible copper wire no less than 1.5mm2 to reliably ground. Zh

★ Connect the aviation plug between the control box and the kettle body.

Five, cement autoclave operating procedures:

★ Open the lid of the kettle and fill the kettle with 5% to 7% ~ 10% of the volume of the kettle, that is, 595cc ~ 850cc of distilled water. (Usually recommended water injection volume: 700 ml to 800 ml)

★ Put the bracket with the test piece in it. Zh

★ Wipe the sealing surface of the kettle mouth and the kettle cover with cotton yarn, and then apply a thin layer of clean oil to the sealing surface of the kettle mouth with a brush. Zh

★ Gently cover the kettle lid, press down and turn the kettle lid left and right to confirm that the joints are properly tight. Screw in 10 female screws by hand. Then use a torque wrench to tighten the nuts evenly in a diagonal sequence in three times according to 50, 100, and 100 Nm, and install the kettle lid. Zh

★ Inject 3 ~ 5 drops of engine oil into the thermometer cannula in the lid of the kettle (generally, the oil level should not be higher than the thermometer mercury ball), and gently insert a 300 ℃ mercury thermometer into the tube. Zh

★ Open either of the two air release valves. Zh

★ Adjust the red upper limit pointer of the electric contact pressure gauge to 2.025MPa (ie: 2MPa and then increase it by half a division); set the green lower limit pointer to 1.975MPa. Zh

★ Close the ventilation plate and ventilation ring. Zh

★ Turn on the power, turn on the main power switch on the control box, press the start key, the running and heating indicator lights up, and the kettle starts to heat at 1800W. At the same time, the digital display time relay starts to display. Zh

★ When water vapor is discharged from an opened air release valve, it means that the internal air has been exhausted. Close the air release valve. After the valve is closed, the pressure will increase as the temperature rises. At this time, pay attention to whether the instrument works abnormally. If it is abnormal, you must find out the reason, or press the stop button to stop the test. Zh

★ After the heating is stopped, the fan will automatically work, the signal light will be on, open the ventilating plate and ventilating ring, there will be hot air discharged from the ventilating ring, and the pressure in the kettle will drop below 0.1MPa within 90min At this time, you can open the air release valve to release the residual pressure in the kettle. Please do not close the air release valve, as it will cause negative pressure in the kettle after cooling and damage the pressure gauge. Zh

★ After cooling to normal temperature, press the stop button, the signal light goes out, the exhaust fan stops, turn off the main power switch, remove the thermometer, and unscrew the 10 captive nuts in the same way as installing the kettle cover (when loosening the nut, use at least two Circulate so as not to damage the sealing joint surface). Remove the lid of the kettle and take out the specimen holder. Use a hose or towel to clean out the distilled water in the kettle. Zh

★ Stop the test procedure halfway: Press the "Stop" key to open the ventilating plate and ventilation ring, and press the "Fan" key. After the instrument has cooled down, reinstall the test.