廠家定制 NLD-3水泥 膠砂 流動度測定儀 水泥電動跳桌 膠砂流動度測定儀 榮計達儀器
面議
上海榮計達實驗儀器有限公司
會員1.png)
上海榮計達實驗儀器有限公司
| 參 考 價 | 面議 |
產品型號
品 牌
廠商性質生產商
所 在 地
聯系方式：王林查看聯系方式
更新時間：2021-07-24 10:37:55瀏覽次數：175次
聯系我時，請告知來自 儀表網一、產品簡介：水泥膠砂流動度測定儀是用于水泥膠砂流動度檢測儀器，水泥膠砂流動度測定儀依據2005年發布的新標準GB/T2419-2005《水泥膠砂流動度測定方法》的流動度試驗，是該標準用儀器
一、產品簡介：
水泥膠砂流動度測定儀是用于水泥膠砂流動度 檢測儀器， 水泥膠砂流動度測定儀依據2005年發布的新標準GB/T2419-2005《水泥膠砂流動度測定方法》的流動度試驗，是該標準用儀器。采用微電腦控制器，自動計數，自動停止，必須可靠接地，用膨脹螺栓固定在基座上。
Product introduction of cement mortar fluidity tester:
The cement mortar fluidity tester is used to measure the cement mortar fluidity The cement mortar fluidity tester is based on the new standard GB / T2419-2005 "Cement mortar fluidity measurement method" released in 2005 The degree test is the instrument specified in this standard. A microcomputer controller is used for automatic counting and automatic stopping. It must be reliably grounded and fixed on the base with expansion bolts.
二、技術參數：
★振動部分總重量：4.35 kg±0.15kg
★振動落距：10mm±0.2mm
★振動頻率：1Hz
★振動次數：25次
★桌面參數：
★材料：鑄鋼，工作面鍍硬鉻
★直徑：φ300mm+1mm
★重量：20kg
Technical parameters of cement mortar fluidity tester
★ Total weight of vibration part: 4.35 kg ± 0.15kg
★ Vibration fall distance: 10mm ± 0.2mm
★ Vibration frequency: 1Hz
★ Vibration times: 25 times
★ Desktop parameters:
★ Material: cast steel, hard chrome plating on the working surface
★ Diameter: φ300mm + 1mm
★ Weight: 20kg
三、安裝步驟：
★必須可靠接地，用膨脹螺栓固定在基座上。
★基座由混凝土澆筑而成(或磚混基礎)，底面尺寸約為400mm×400mm，高約690mm。在基座和儀器機架之間宜填墊圈，可通過調整墊圈高度調節桌面水平。
★儀器安裝后，其桌面沿彼此成直角的兩個直徑方向測量時均應成水平。跳桌安裝好后，采用流動度標準樣(JBW01-1-1)進行檢定，測得的流動度值如與給定的標樣流動度值相差在規定范圍內, 則該跳桌的安裝及使用性能合格。
Third, the installation steps of cement mortar fluidity tester:
★ It must be reliably grounded and fixed on the base with expansion bolts.
★ The base is cast by concrete (or brick-concrete foundation), the bottom surface size is about 400mm × 400mm, and the height is about 690mm. A gasket should be filled between the base and the instrument rack. The height of the table can be adjusted by adjusting the height of the gasket.
★ After the instrument is installed, its table should be level when measured along two diameter directions that are at right angles to each other. After the jumping table is installed, the fluidity standard sample (JBW01-1-1) is used for verification. If the measured fluidity value is within the specified range from the given standard sample fluidity value, the installation and Qualified performance.
四、使用方法：
★試樣的制作與填裝方法按GB2419-2005和GB17671-1999的有關規定，也可參照本說明書附錄。
★ 使用前，請用檢規檢查落距。
★ 將插頭接入計數器后對應孔內，將計數器接通電源。
★如跳桌在24小時內未被使用，先空跳一個周期25次。
Fourth, the use of cement mortar fluidity tester:
★ The method of making and filling the samples is in accordance with the relevant regulations of GB2419-2005 and GB17671-1999, and can also refer to the appendix of this manual.
★ Before use, please check the landing distance with inspection rules.
★ Connect the plug into the corresponding hole of the counter, and then turn on the counter.
★ If the table is not used within 24 hours, first skip a cycle 25 times.
五、維護與保養：
使用完畢后，應擦凈儀器，清除儀器周圍殘留膠砂，用輕油稍稍潤滑推桿、桌面和凸輪表面。長期不用，儀器應防塵保護，控制器放置在包裝盒內。
如儀器不計數，請檢查接近開關是否松動、與凸輪間隙是否為1mm~2mm，如有偏離或松動，請調整間隙后緊固
Fifth, maintenance and maintenance of cement mortar fluidity tester:
After use, the instrument should be cleaned to remove the residual rubber sａnd around the instrument, and lightly lubricate the surface of the push rod, table and cam. If not used for a long time, the instrument should be protected from dust and the controller should be placed in the box.
If the instrument does not count, please check whether the proximity switch is loose and whether the clearance between it and the cam is 1mm ~ 2mm. If it is deviated or loosened, please adjust the clearance and tighten
您感興趣的產品PRODUCTS YOU ARE INTERESTED IN
儀表網 設計制作，未經允許翻錄必究 .? ? ?
請輸入賬號
請輸入密碼
請輸驗證碼
桐梓县|
张家口市|
富平县|
丰顺县|
奎屯市|
饶阳县|
德安县|
雅江县|
葫芦岛市|
益阳市|
乐业县|
凤冈县|
玉田县|
尤溪县|
上饶市|
霍邱县|
霍山县|
克山县|
章丘市|
浙江省|
深州市|
浮山县|
巩留县|
紫阳县|
手机|
河津市|
佛学|
台东市|
武清区|
泸州市|
玉溪市|
新晃|
宣武区|
儋州市|
玉环县|
宜兰县|
玉山县|
台中县|
苍溪县|
潼南县|
莱州市|