1.煙度計/ 型號：NTP1-HPC601

煙度計/主要功能特點：
     一體化結構設計；
      采用分流式取樣技術、柴油機加速、減速和穩速時均可測量煙度；
      數據自動線性化處理，可顯示不透光度N、光吸收系數K和對應濾紙式煙度值SF；
      高亮度數碼顯示；
      采用“空氣幕"技術保護光學系統免受污染；
      檢測室自動恒溫控制，可防冷凝而影響測試精度；  
      附自動時間顯示,可選配轉速測量和油溫測量；
      出現故障自動診斷顯示所在單元；
      配內置打印機（或數字RS－232A接口或模擬接口）。 
主要技術參數：

測量范圍              不透光度N:0～(相當煙度值0～10FSN) 

   光吸收系數K:0～16.06m^-1

示值誤差              ≤±2%(測量值)

穩定性                自動校零，量矩漂移≤±1%/4h

重復性                重復誤差≤±1%

分辨率                0.1%

輸出方式              數字直讀顯示，可附打印機打印煙濃度(暗度)大值，測試

                      時間、日期等?？筛浇涌谂c計算機聯網

測量煙度溫度          70℃(自動恒溫)，當溫度誤差≥±10%時，溫度及錯誤指示

                      燈亮

環境條件              溫度0～40℃，相對濕度≤90%

電源                  AC100-240V 50Hz 消耗功率150VA

外形尺寸（含支架）    160mm(深)×400mm(寬)×480mm(高) 

重量                  約8kg

Main Features:

◆Integrated Structural Design
◆Adopted a triage-type sampling technique, diesel engine acceleration, deceleration, and steady speed can be measured when the smoke
◆Linear automatic data processing, can be displayed opacity degrees N, light absorption coefficient K and the corresponding value of filter paper-type smoke SF
◆High-brightness digital display;
◆Use of "air curtain" technology to protect the optical system from pollution
◆Automatic detection of room temperature control, anti-condensation can affect the testing accuracy
◆Automatically attached to the time display, and optional speed measurement and oil temperature measurement
◆Show where the failure of automatic diagnosis unit;
◆Equipped with built-in printer (or digital RS-232A interface or analog interface)

Main technical parameters:

Test Scope：No light transmission N:：0～ (equivalent to smoke value 0 ~ 10FSN)

Light absorption coefficient K：0-16 .06 m^-1 
Shows the value error：≤ ± 2% (measured value)
Stability：Automatic zero, volume moments drift ≤ ± 1% / 4h
Repeatability：Repeat the error ≤ ± 1%
Resolution：0.1%
Output Mode：Digital direct-reading shows that smoke concentrations can be attached

printer (dark degrees) the maximum test time, date and so on. Can be

attached to interface with the computer network
Measurement of smoke temperature：70 ℃ (automatic constant temperature), when

the temperature error of ≥ ± 10%, the temperature and the error

indicator light
Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V  50Hz Power consumption 150VA
Dimensions (with stand)：160mm (depth) × 400mm (width) × 480mm (H)
Weight：About 8kg

2.全自動濾紙式煙度計  濾紙式煙度計 煙度計 型號：NTP1-HPC701

主要功能特點：
全自動濾紙式煙度計，用于柴油車自由加速狀態下排煙的煙度測量。自動完成測量全過程，自動顯示1、2、3次測量值及其平均值，高亮度數碼管顯示，附時間顯示，出現故障自動診斷顯示所在單元，可配內置打印機（或數字RS－232A接口或模擬接口）

主要技術參數：

Main Features:

Automatic filter paper-type smoke meter for diesel vehicles free of tobacco smoke accelerate the state measurement. Auto-complete measurement of the whole process automatically 1,2,3 times measured values and their average, high-brightness LED display, with a time display, automatic fault diagnosis shows there where the unit can be equipped with built-in printer (or digital RS-232A interface or analog interface)

Main technical parameters:

Range：0 ~ 10FSN
Indication error：≤ ± 3%
Repeatability：Repeat error ≤ ± 2%
Stability：Zero drift ≤ ± 3%
Exhaust volume sampling system：300 ± 15ml
Tightness：≤ 15ml/min
Effective working diameter of filter paper：30.7mm
Pumping action time：1.4 ± 0.2s
Environmental conditions：Temperature 5 ~ 40 ℃, relative humidity ≤ 90%

Power ：AC220v ± 10% 50Hz Power consumption 150VA
Dimensions： 520mm (length) × 360mm (width) × 200mm (H)
Weight：about 30kg

3.汽車排氣分析儀 排氣分析儀 型號：NTP1-HPC302

主要功能特點：
　　

   用于測量汽車排放廢氣中的HC、CO、NO_x氣體濃度，采用*進技術，進口關鍵零部件組裝而成。具有高亮度數碼顯示，自動校零，自動數據線性化處理，氣路阻塞時自動報警，故障時自動診斷所在單元，打印測試之日期、時間功能，配內置打印機（或模擬輸出接口或RS－232A數字串行通信接口），可進行自由怠速和雙怠速測量，具有操作方便，測量數據準確，工作穩定可靠等特點。 

主要技術參數：

測量范圍              HC：0～10000×10^-6（ppm）vol

                      CO: 0～10   ×10^-2(%)vol

                      NO_x :0～4000 ×10^-6（ppm）vol

示值誤差              HC±12  ×10^-6（ppm）vol(誤差)或±5%(相對誤差)

                      CO±0.06×10^-2(%)vol    (誤差)或±5%(相對誤差)

                      NO_x ± 25×10^-6（ppm）vol(誤差)或±4%(相對誤差)

重復性                重復誤差≤±2%

分辨率                HC：1×10^-6（ppm）vol

                      CO: 0.01×10^-2(%) vol

                      NO_x:1×10^-6（ppm）vol

穩定性                自動校零，量矩漂移≤±3%

預熱時間              8min（可預熱3min應急檢測）

響應時間              95%響應不大于10秒

輸出方式              數字直讀顯示，可附打印機打印氣體名稱，濃度大值，測

                      試時間、日期等?？筛浇涌谂c計算機聯網

環境條件              溫度0～40℃，相對濕度≤90%

電源                  AC100-240V 50Hz 或DC12V（選加電源逆變器）

                      消耗功率50VA

外形尺寸              420mm(長)×310mm(寬)×170mm(高)

重量                  約9KG

Main Features:

Used to measure vehicle emissions of HC, CO, NOx gas concentration, using advanced foreign technology, import the key components assembled. With a high-brightness digital display, automatic zero, linear automatic data processing, auto-alarm when the gas line blocking, fault diagnosis where the unit automatically and print testing date, time functions, with built-in printer (or the analog output interface or RS -232A digital serial communication interface), can be freely idling and dual idling measure, with easy operation, accurate measurement data, work stable and reliable characteristics.

Main technical parameters:

Test Scope：HC：0～10000×10^-6（ppm）vol

CO：0～10×10^-2(%) vol

NOx：0～4000×10-6（ppm）volShows the value error：HC ± 12×10-6（ppm）vol (absolute error)or± 5% (relative error)

CO± 0.06×10^-2(%) vol   (absolute error)or± 5% (relative error)

NO_x±25×10^-6（ppm）vol  ( absolute error) or ±4%(relative error)
Stability：Automatic zero, volume moments drift ≤ ± 3%
Repeatability：Repeat error ≤ ± 2%
Resolution：HC：1×10^-6（ppm）vol

CO：0.01×10^-2(%) vol

NO_x：1×10^-6（ppm）vol
Response Time：95% of the response to no more than 10 seconds
Warm-up Time：8 min（May the preheating 3min urgent examination）

Output Mode：Digital direct-reading show that gases can be attached printer name, the

concentration maximum, average and minimum test time, date, etc.. Can be attached to interface with the computer network

Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V  50Hz or DC12V (select plus power inverter) Power

consumption 50VA
Dimensions：420mm (length) × 310mm (width) × 170mm (H)
Weight：About 9kg

4.摩托車排氣分析儀  摩托車排氣檢測儀 型號：NTP1-HPC211

主要功能特點：
　　分體式結構設計，操作方便，按新國標GBl9758-2005技術要求研制；
　　采用內置全流式取樣技術，測量摩托車急加速、怠速工況時的煙度；
　　高亮度數碼顯示，進口關鍵零部件組裝而成；
　　采用全流式耐高溫的特殊取樣探頭，采樣穩定、精確、方便；
　　丌機預熱時間10分鐘，并自動調零；
　　數據自動線性化處理，可顯示不透光度N、光吸收系數K；
　　出現故障時自動顯示故障代碼；
　　附有自動時鐘顯示，內置打印機(RS—232或模擬接口聯網)供選擇。
主要技術參數：

測量范圍              不透光度N:  0～

   光吸收系數K:0～90.65m^-1

示值誤差              ≤±2%

穩定性                自動校零，量矩漂移≤±1%/4h

分辨率                0.1%

響應時間              1S±0.1S

輸出方式              LED(4位)顯示，可附打印機，打印出5組急加速煙度、怠速

                      煙度、光吸收系數的大值及平均值，測試時間、日期等，

                      可附接口與計算機聯網

環境條件              溫度0～40℃，相對濕度≤90%

電源                  AC100-240V   50Hz 消耗功率150VA

外形尺寸              控制箱：250mm(長)×310mm(寬)×170mm(高)

                      煙道箱：250mm(長)×170mm(寬)×170mm(高)

重量                  控制箱：4kg，煙道箱：5kg

Main Features:

◆Separated structural design, easy to operate, according to the new national standard GBl9758-2005 technical requirements for development.
◆With built-in full-flow sampling techniques, application-specific measurement of motorcycle hard phases of acceleration, idle condition when the smoke.
◆High-brightness digital display, import key components assembled.
◆Using a special full-flow high-temperature sampling probe, sampling a stable, accurate and convenient.
◆Ji machine warm-up time 10 minutes, and automatic zero adjustment.
◆Linear automatic data processing, can be displayed opacity degrees N, light absorption coefficient K.
◆Fails automatically displays fault code.
◆With automatic clock display, built-in printer (RS-232 or analog interface network) for selection.

Main technical parameters:

Test Scope：No light transmission N: 0～ 

Light absorption coefficient K: 0～90.65 m-1Shows the value error：≤ ± 2%Stability：Automatic zero, volume moments drift ≤ ± 1% / 4hResolution：0.1%Response Time：1S ± 0.1SOutput Mode：LED (4-bit) display can be attached to the printer 5 groups hard phases    

of acceleration smoke, idle smoke, the light absorption coefficient of

the maximum and the average test time, date, etc., can be attached to

interface with the computer network
Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V  50Hz Power consumption 150VA
Dimensions：Control Box: 250mm (length) × 310mm (width) × 170mm (H)
            Flue Box: 250mm (length) × 170mm (width) × 170mm (H)
Weight：Control box: 4kg, flue box: 5kg

5.汽車排氣分析儀 排氣分析儀 汽車排氣檢測儀 型號：NTP1-HPC201

主要功能特點：
　　

    用于測量汽車排放廢氣中的HC及CO氣體濃度，采用*進技術，進口關鍵零部件組裝而成。具有高亮度數碼顯示，自動校零，自動數據線性化處理，氣路阻塞時自動報警，故障時自動診斷所在單元，打印測試之日期、時間功能，配內置打印機（或模擬輸出接口或RS－232A數字串行通信接口），可進行自由怠速和雙怠速測量，具有操作方便，測量數據準確，工作穩定可靠等特點。 
主要技術參數：

測量范圍              HC：0～10000×10^-6（ppm）vol

   CO: 0～10   ×10^-2(%)vol

示值誤差              HC±12  ×10^-6（ppm）vol(誤差）或±5%（相對誤差）

   CO±0.06×10^-2(%)vol    (誤差）或±5%（相對誤差）

穩定性                自動校零，量矩漂移≤±3%

重復性                重復誤差≤±2%

分辨率                HC：1×10^-6（ppm）vol

                      CO: 0.01×10^-2(%)vol

響應時間              95%響應不大于10秒

預熱時間              8min（可預熱3min應急檢測）

輸出方式              數字直讀顯示，可附打印機打印氣體名稱，濃度大值、平

                      均值、小值，測試時間、日期等?？筛浇涌谂c計算機聯網

環境條件              溫度0～40℃，相對濕度≤90%

電源                  AC100-240V 50Hz 或DC12V（選加電源逆變器）

                      消耗功率50VA

外形尺寸              420mm(長)×310mm(寬)×170mm(高)

重量                  約9kg

Main Features:

Used to measure vehicle emissions of HC and CO gas concentrations, using advanced foreign technology, import the key components assembled. With a high-brightness digital display, automatic zero, linear automatic data processing, auto-alarm when the gas line blocking, fault diagnosis where the unit automatically and print testing date, time functions, with built-in printer (or the analog output interface or RS -232A digital serial communication interface), can be freely idling and dual idling measure, with easy operation, accurate measurement data, work stable and reliable characteristics.

Main technical parameters:

Test Scope：HC：0～10000×10^-6（ppm）vol

CO：0～10  ×10^-2(%) vol

Shows the value error：HC ± 12×10-6（ppm）vol (absolute error)or± 5% (relative error)

CO± 0.06×10^-2(%) vol   (absolute error)or± 5% (relative error)

Stability：     Automatic zero, volume moments drift ≤ ± 3%
Repeatability： Repeat error ≤ ± 2%
Resolution：   HC：1×10^-6（ppm）vol

CO：0.01×10^-2(%) vol

Response Time：95% of the response to no more than 10 secondsWarm-up Time：8 min（May the preheating 3min urgent examination）Output Mode：Digital direct-reading show that gases can be attached printer name, the

concentration maximum, average and minimum test time, date, etc.. Can be attached to interface with the computer network

Environmental conditions：Temperature 0 ~ 40 ℃, relative humidity ≤ 90%
Power：AC100-240V  50Hz or DC12V (select plus power inverter) Power

consumption 50VA
Dimensions：420mm (length) × 310mm (width) × 170mm (H)
Weight：About 9kg

溫馨提示：以上產品資料和圖片全都是按照順序相對應的