熱流道專業術語中英對照
入水：gate
進入位： gate location 水口形式：gate type 大水口：edge gate
細水口： pin-point gate 水口大?。?span lang="EN-US">gate size
轉水口：tching runner/gate 唧嘴口徑： sprue diameter
流道: runner
熱流道： hot runner,hot manifold 熱嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate
圓形流道：round(full/half runner 流道電腦分析：mold flow analysis 流道平衡:runner balance 熱嘴： hot sprue
熱流道板：hot manifold 發熱管：cartridge heater 探針: thermocouples 插頭： connector plug 插座： connector socket 密封/封料： seal
運水：water line 喉塞：line lpug 喉管：tube
塑膠管：plastic tube
快速接頭：jiffy quick connector plug/socker
模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold
邊釘/導邊：leader pin/guide pin 邊司/導套：bushing/guide bushing 中托司：shoulder guide bushing 中托邊l：guide pin
頂針板：ejector retainner plate
托板： support plate 螺絲： screw 管釘：dowel pin
開模槽：ply bar scot
內模管位：core/cavity inter-lock 頂針： ejector pin 筒：ejector sleeve 司筒針：ejector pin 推板：stripper plate
縮呵：movable core,return core core puller 扣機（尼龍拉勾）：nylon latch lock 斜頂：lifter 模胚（架）： mold base 上內模：cavity insert 下內模：core insert 行位（滑塊）： slide 鑲件：insert
壓座/斜雞：wedge
耐磨板/油板：wedge wear plate 壓條：plate
撐頭: support pillar 唧嘴： sprue bushing 擋板：stop plate
定位圈：locating ring 鎖扣：latch
扣雞：parting lock set 推桿：push bar 栓打螺絲：s.h.s.b 頂板：eracuretun 活動臂：lever arm 分流錐：spure sperader 水口司:bush
垃圾釘：stop pin 隔片：buffle
**柱：spring rod **:die spring
中托司：ejector guide bush 中托邊：ejector guide pin 鑲針：pin
銷子：dowel pin 波子**：ball catch 喉塞: pipe plug 鎖模塊：lock plate 斜頂：angle x pin
斜頂桿：angle ejector rod 尼龍拉勾：parting locks 活動臂：lever arm
復位鍵、提前回桿：early return bar 氣閥：valves
斜導邊：angle pin 術語：terms
承壓平面平衡：parting surface support balance 模排氣：parting line venting
回針碰料位：return pin and cavity interference ?？偢叱銎C(jī)規格：mold base shut hight 頂針碰運水：water line interferes withejector pin 料位出上/下模：part x cavith (core) side
模胚原身出料位：cavity direct cut on a-plate,core direct cut on b-plate. 不準用鑲件： do not use (core/cavity) insert 用鈹銅做鑲件： use beryllium copper insert
初步（正式）模圖設計：preliinary (final) mold design 反呵：reverse core
**壓縮量：spring compressed length 穩定性好：good stability,stable 強度不夠：insufficient rigidity 均勻冷卻：even cooling 扣模：sticking
熱膨脹：thero expansion 公差：tolorance 銅公(電極）：copper electrode 模
注塑模部分中英文對照
塑料成形模具mould for plastics 熱塑性塑料模mould for thermoplastics 熱固性塑料模mould forthermosets
壓縮模compression mould 壓注模、傳遞模transfermould 注射模injection mould
熱塑性塑料注射模 injection mould for thermoplastics 熱固性塑料注射模 injection mould for thermoses
成形零件 定模stationary mould fixed half 動模movable mould moving half
定模座板fixed clamp plate, top clamping plate. top plate 動模座板moving clamp plate. bottom clamping plate. bottom plate 上模座板upper clamping plate 下模座板 lower clampingplate 凹模固定板 cavity-retainer plate
型芯固定板core-retainer plate 凸模固定板punch-retainer plate 模套 chase. bolster.frame
支承板backing plate. supprr plate 墊塊 spacer parallel
支架ejector housing. mould baseleg 動模movable mouldmovinghalf 定模座板 fixed clamp plate, top clamping plate. top plate
動模座moving clamp plate. bottom clamping plate. bottomplate 上模座板upper clampingplate 下模座板 lower clamping plate
凹模固定板cavity-retainerplate 型芯固定板core-retainerplate 凸模固定板punch-retainer plate 模套chase. bolster. Frame 墊塊spacerparallel 支架ejector housing. mould baseleg 壓力鑄造模具 die-casting die
壓鑄模零部件
定模fixed die, coverdie 定模座板fixed clampingplate 定模套板 bolstor, fixeddie 動模moving die,ejector die
動模座板moving clampingpla 直流道sprue 橫流道runner 內澆口 gate
會員1.png)