江蘇春晨電纜有限公司：http://m.liuyangwu.com/st82365/
Technical specification for thermal shrinkage end caps for cablesFDZ-YEYH風能電纜
1范圍，FDZ-YEYH風能電纜
1 range
Requirements, inspection rules, marking, packaging, transportation and storage of the materials for the thermal contraction end caps (hereinafter referred to as the head cap) for the cables are specified in this specification.
2規格
2 specifications
封頭帽的規格見表1
The specification of the head cap is shown in Table 1
表1 電纜用熱收縮封頭帽的規格
Table 1 specifications of thermal shrinkage cap for cable
序號 直徑×柱高 電纜外徑 序號 直徑×柱高 電纜外徑 序號 直徑×柱高 電纜外徑
Diameter * height of cable diameter * diameter * height of cable diameter * diameter * height of cable diameter
1 10×40 7～9 13 35×80 27～30 25 80×90 70～75
110 * 407 ~ 91335 * 8027 ~ 302580 * 9070 ~ 75
2 13×40 7～12 14 40×55 30～35 26 80×120
213 * 407 ~ 121440 * 5530 ~ 352680 * 120
3 15×40 11～13 15 45×55 35～40 27 85×90 75～80
315 * 4011 ~ 131545 * 5535 ~ 402785 * 9075 ~ 80
4 18×40 13～15 16 50×70 40～45 28 85×120
418 * 4013 ~ 151650 * 7040 ~ 452885 * 120
5 20×40 14～18 17 55×70 55～50 29 90×120 80～89
520 * 4014 ~ 181755 * 7055 ~ 502990 * 12080 ~ 89
6 20×70 18 60×70 50～55 30 90×150
620 * 701860 * 7050 ~ 553090 * 150
7 23×40 15～20 19 60×90 50～55 31 100×120 90～95
723 * 4015 ~ 201960 * 9050 ~ 5531100 * 12090 ~ 95
8 25×40 18～22 20 65×90 55～60 32 100×150
825 * 4018 ~ 222065 * 9055 ~ 6032100 * 150
9 28×40 20～25 21 70×90 60～65 33 110×120 95～105
928 * 4020 ~ 252170 * 9060 ~ 6533110 * 12095 ~ 105
10 30×55 22～27 22 70×120 34 120×150
1030 * 5522 ~ 272270 * 12034120 * 150
11 30×80 22～27 23 75×90 65～70 35 130×150 95～105
1130 * 8022 ~ 272375 * 9065 ~ 7035130 * 15095 ~ 105
12 35×55 27～30 24 75×120 - - -
1235 * 5527 ~ 302475 * 120 ---
3技術要求
3 technical requirements
見表2。
See table 2.
表2 檢測項目及要求
Table 2 test items and requirements
序號 檢測項目 要 求
Serial number detection project requirements
1 外觀 表面平整，色深均勻，無裂紋等缺陷
1 appearance surface smooth, uniform color, no cracks and other defects
2 直徑及柱高 符合表1的固定
2 diameter and height of the column are in compliance with the fixed table 1.
3 收縮率 徑向 150℃ 15min 45
3 shrinkage rate radial 150 C 15min 45
縱向 150℃ 15min 20
Longitudinal 150 C 15min 20
4 收縮溫度 ℃ 150～160
4 shrinkage temperature 150 ~ 160
5 偏心度 % ≤30
5 eccentricity% less than or equal to 30
6 抗張強度 Mpa ≥16.7
6 the tensile strength of Mpa = 16.7
7 斷裂伸長率 % 300
7 elongation at break% 300
8 密封性 0.1MPa 1h 不漏氣
8 sealing 1H 0.1MPa no leakage
4 檢驗規則
4 inspection rules
4.1不定期抽檢，每月至少一次，性能依據封頭帽的質保書或檢測報告驗收。
4.1 random sampling, at least once a month, performance based on header cap quality assurance book or test report.
4.2對每批封頭帽必須附有供方材料的質保書或檢測報告。
4.2 for each batch of head cap must be accompanied by the supplier's material quality assurance book or test report.
5包裝
5 packaging
封頭帽應包裝在PP紡織物或經公司同意的其它包裝物內。
The head cap should be packed in PP fabric or other packing material which is agreed by the company.
6標志
6 mark
封頭帽包裝上應標明：廠家名稱、商標、產品名稱、批號、規格、顏色、數量等。
Seal cover should be marked on the package: manufacturer name, trademark, product name, batch number, specifications, color, quantity, etc..
7附件
7 attachment
封頭帽交貨時必須附有產品合格證和質量保證書。供貨時，必須附有法定檢驗部門的型式試驗報告。
Delivery of the head cap must be accompanied by a certificate of conformity and quality assurance. For the first time, the type test report of the statutory inspection department must be attached.
8貯存及運輸
8 storage and transportation
封頭帽應貯存在干燥的庫房內，不應靠近火源，免受陽光直射。貯存期限從生產日期起為１２個月，超過貯存期后，應重新檢驗，合格后方可使用。
Head cap should be stored in a dry warehouse, should not be close to the fire source, avoid direct sunlight. Storage period from the production date of 12 months, more than the storage period, should be re tested, qualified rear can be used.
灌南县|
视频|
新丰县|
商河县|
阿克苏市|
钟祥市|
勐海县|
昌吉市|
招远市|
寿光市|
巴彦淖尔市|
金川县|
南澳县|
高阳县|
德庆县|
海晏县|
龙泉市|
陆河县|
新晃|
济南市|
池州市|
英吉沙县|
济宁市|
肇东市|
凭祥市|
波密县|
祁连县|
沐川县|
页游|
张家港市|
松江区|
西乌珠穆沁旗|
隆昌县|
文登市|
黑水县|
岱山县|
南川市|
竹山县|
顺昌县|
海兴县|
大理市|