ELAG OPTIMESS®無接觸激光測量技術在厚度測量中的應用

來源：瑞士ELAG有限公司北京代表處 2008年11月24日 16:35

Thickness measurement

厚度測量

Research & development

For thickness measurement, OPTIMESS laser triangulation sensors, OPTISCAN laser triangulation scanners or light section sensorsOPTIMESS shadow measuring systems are used. The advantages of the laser measuring technique in the field of thickness measurement are:

l no material contact

l Independent of the colour of the material by control of the laser power

l independent of the composition of the material

l high local resolution due to small measuring spot

l high measuring frequency (up to 50 kHz)

l great distance from material possible In measurements on hot surfaces possible

研究和發展

對厚度測量，可采用OPTIMESS激光三角測量儀、OPTISCAN激光三角掃描儀或光切傳感儀和OPTIMESS影子測量系統，這些厚度測量技術主要優勢體現如下：

l 非接觸測量

l 可控制激光功率，測量不受材料顏色影響，

l 不受材料成分影響

l 小光斑、高分辨率

l 高速測量，頻率達50KHz

l 對熱表面材料，可以遠距離測量

Thickness measurement (singlemulti-track)

The thickness measurement is performed directly at the point where the laser beam hits the object in the case of stationary objectsalong the line which the laser point projects onto the material in the case of measuring objects passing by underneath the sensor. The measurement can be made as a reference measurement with one sensor or As a thickness measurement with two sensors per measuring track. C-brackets, 0-frames or complete measuring modules with automatic calibrationtheir own drive belts are available as measuring frames.

厚度測量（單軌和多軌）

厚度測量通過激光光束直達被測對象表面，并在線檢測在激光傳感器下運行的被測對象。單傳感器可參考測量厚度，雙傳感器可實單軌、C拱、O幀或*測量模式，測量架可自動校準并且自行驅動傳送帶。

Linear thickness measurement (scanning or traversing)

This thickness measurement takes place with OPTISCAN laser scanners or light-section sensors or over greater widths with a traversing mechanismtwo punctiform OPTIMESS laser sensors. The lateral position is picked up as an additional value apart from the distance information by the laser scanners so that the thickness or the thickness profile along the scanned line is recorded. Over smaller widths the laser scanners or light-section sensors offer the advantage that no additionally moved parts are necessaryscanning frequencies of about 20 Hz are possible. On the other hand, the traversing mechanics, designed as a C-frame, offer the possibility of reaching measuring widths up to 5 metres.

在線厚度測量（掃描和方向機）

厚度測量可以采用OPTISCAN激光掃描儀、光切傳接器、或者帶雙OPTIMESS激光傳感器方向機的超寬測量。激光掃描儀在線記錄側面位置和厚度狀態。

窄物體測量，激光掃描儀或光切傳感器無不需運動器件，掃描頻率達20Hz.

另外，設計為C架式的方向機，測量寬度高達5米。

Thickness measurement according to the shadow principle

In the shadow principle with OPTILINE sensors a laser line of parallel light is generatedprojected on a CCD line opposite. When a material Is Inserted In the measuring gap this leads to a partial shadowing of the laser line on the detector. For thickness measurement it is necessary for the material to be measured to be deflected by a roller. The difference between the roller (zero)the material surface picked up by the shadow measurement system is the material thickness.

影子原理厚度測量

根據影子原理的OPTILINE激光儀收集平行光并映射到CCD。當被測對象置于測量間隙，檢測激光陰影。厚度測量要測量被測對象在滾筒上編移，以滾筒為零點，測量滾筒陰影與被測物陰影差為被測物的厚度。

(瑞士EL*公司北京代表處供稿)

相關產品

免責聲明

凡本網注明“來源：儀表網”的所有作品，均為浙江興旺寶明通網絡有限公司-儀表網合法擁有版權或有權使用的作品，未經本網授權不得轉載、摘編或利用其它方式使用上述作品。已經本網授權使用作品的，應在授權范圍內使用，并注明“來源：儀表網”。違反上述聲明者，本網將追究其相關法律責任。
本網轉載并注明自其它來源（非儀表網）的作品，目的在于傳遞更多信息，并不代表本網贊同其觀點或和對其真實性負責，不承擔此類作品侵權行為的直接責任及連帶責任。其他媒體、網站或個人從本網轉載時，必須保留本網注明的作品第一來源，并自負版權等法律責任。
如涉及作品內容、版權等問題，請在作品發表之日起一周內與本網聯系，否則視為放棄相關權利。

沈樵综合在线,一区二区三区乱码,免费资源一区二区三区,91超碰碰,av极品一线天,日韩免费高清一区二区,国产蜜尤福利在线,嗯啊91在线观看,精品一区二三

ELAG OPTIMESS®無接觸激光測量技術在厚度測量中的應用

免責聲明