PZRD4509瀝青針入度測定器
一、概述
瀝青針入度試驗器是根據中華人民共和國國家標準GB/T4509《石油瀝青針入度測定法》、GB/T269《潤滑脂和石油脂錐入度測定法》及中華人民共和國交通行業標準JTJ052-2000《公路工程瀝青及瀝青混合料試驗規程》—T0604《瀝青針入度試驗》中的技術要求和有關規定設計制造的。
二、主要機能
1、主機,配套時間控制器,用時間控制器控制電磁鐵的吸合釋放,使推桿下落鎖緊.
2、時間控制器采用數字顯示,控制范圍0 ～ 60控制時間精度為±0.1秒.
3、采用液晶數字清零的百分毫米標尺式深度測量機構,使用方便、快速.
4、大可測錐入度值不少于780單位,能適應各項試驗要求.
5、支架移動分別有快速和微動兩種速度,便于測試操作時的尖針對準試樣表面,快速移動手輪在儀器左面,微動手輪在儀器的右面.
6、支架有隨時自鎖功能,任何位置都能自動穩固停住.
7、具有臺面水平調節機構,調節方便.
8、附有手動釋放錐入件的機構,可確保在使用時,自行控制.
9、控溫范圍常溫-60℃。
三 參數
1、工作電源：220V±10%，50Hz
2、顯示單位：0.1
3、大量程：700
4、計時范圍：5-60S
6、計量精度：±0.01秒
7、控溫精度：±0.1℃
7、大功率：200W
PZRD4509 Asphalt Penetration Tester
I. Overview
Asphalt penetration tester is based on the Peoples Republic of China National Standard GB / T4509 "Petroleum Asphalt Penetration Test Method", GB / T269 "Grease and Petroleum Grease Penetration Test Method" and the Peoples Republic of China Transportation Industry Standard JTJ052- 2000 "Technical Specification for Asphalt and Asphalt Mixtures of Highway Engineering"-T0604 "Asphalt Penetration Test" technical requirements and relevant regulations are designed and manufactured.
2. Main functions
1.The host machine is equipped with a time controller.The time controller is used to control the suction and release of the electromagnet to make the push rod fall and lock tightly.
2. The time controller uses digital display, the control range is 0 ~ 60, and the control time accuracy is ± 0.1 seconds.
3.Using the LCD digital zero-clearing millimeter scale depth measurement mechanism, it is convenient and fast to use.
4.The maximum measurable cone penetration value is not less than 780 units, which can adapt to various test requirements.
5.The bracket movement has two speeds of fast and fine movement, which is convenient for the pointed surface of the sample during the test operation.The fast-moving handwheel is on the left side of the instrument, and the fine-motion handwheel is on the right side of the instrument.
6.The bracket has a self-locking function at any time, and it can be automatically and firmly stopped at any position.
7.It has a table level adjustment mechanism, which is convenient to adjust.
8.A mechanism with a manual release cone is ensured to ensure self-control when in use.
9. Temperature control range: normal temperature -60 ℃.
Three parameters
1. Working power supply: 220V ± 10%, 50Hz
2. Display unit: 0.1
3. Maximum range: 700
4. Timing range: 5-60S
6. Measurement accuracy: ± 0.01 seconds
7. Temperature control accuracy: ± 0.1 ℃
7. Maximum power: 200W
一、概述
瀝青針入度試驗器是根據中華人民共和國國家標準GB/T4509《石油瀝青針入度測定法》、GB/T269《潤滑脂和石油脂錐入度測定法》及中華人民共和國交通行業標準JTJ052-2000《公路工程瀝青及瀝青混合料試驗規程》—T0604《瀝青針入度試驗》中的技術要求和有關規定設計制造的。
二、主要機能
1、主機,配套時間控制器,用時間控制器控制電磁鐵的吸合釋放,使推桿下落鎖緊.
2、時間控制器采用數字顯示,控制范圍0 ～ 60控制時間精度為±0.1秒.
3、采用液晶數字清零的百分毫米標尺式深度測量機構,使用方便、快速.
4、大可測錐入度值不少于780單位,能適應各項試驗要求.
5、支架移動分別有快速和微動兩種速度,便于測試操作時的尖針對準試樣表面,快速移動手輪在儀器左面,微動手輪在儀器的右面.
6、支架有隨時自鎖功能,任何位置都能自動穩固停住.
7、具有臺面水平調節機構,調節方便.
8、附有手動釋放錐入件的機構,可確保在使用時,自行控制.
9、控溫范圍常溫-60℃。
三 參數
1、工作電源：220V±10%，50Hz
2、顯示單位：0.1
3、大量程：700
4、計時范圍：5-60S
6、計量精度：±0.01秒
7、控溫精度：±0.1℃
7、大功率：200W
PZRD4509 Asphalt Penetration Tester
I. Overview
Asphalt penetration tester is based on the Peoples Republic of China National Standard GB / T4509 "Petroleum Asphalt Penetration Test Method", GB / T269 "Grease and Petroleum Grease Penetration Test Method" and the Peoples Republic of China Transportation Industry Standard JTJ052- 2000 "Technical Specification for Asphalt and Asphalt Mixtures of Highway Engineering"-T0604 "Asphalt Penetration Test" technical requirements and relevant regulations are designed and manufactured.
2. Main functions
1.The host machine is equipped with a time controller.The time controller is used to control the suction and release of the electromagnet to make the push rod fall and lock tightly.
2. The time controller uses digital display, the control range is 0 ~ 60, and the control time accuracy is ± 0.1 seconds.
3.Using the LCD digital zero-clearing millimeter scale depth measurement mechanism, it is convenient and fast to use.
4.The maximum measurable cone penetration value is not less than 780 units, which can adapt to various test requirements.
5.The bracket movement has two speeds of fast and fine movement, which is convenient for the pointed surface of the sample during the test operation.The fast-moving handwheel is on the left side of the instrument, and the fine-motion handwheel is on the right side of the instrument.
6.The bracket has a self-locking function at any time, and it can be automatically and firmly stopped at any position.
7.It has a table level adjustment mechanism, which is convenient to adjust.
8.A mechanism with a manual release cone is ensured to ensure self-control when in use.
9. Temperature control range: normal temperature -60 ℃.
Three parameters
1. Working power supply: 220V ± 10%, 50Hz
2. Display unit: 0.1
3. Maximum range: 700
4. Timing range: 5-60S
6. Measurement accuracy: ± 0.01 seconds
7. Temperature control accuracy: ± 0.1 ℃
7. Maximum power: 200W
肇源县|
巴彦县|
正安县|
汝城县|
库尔勒市|
乳源|
阿荣旗|
固阳县|
秀山|
日土县|
天水市|
长子县|
黄龙县|
郓城县|
河津市|
滦平县|
清远市|
东明县|
都安|
竹山县|
禄劝|
百色市|
图片|
武城县|
班戈县|
嘉善县|
高尔夫|
句容市|
和政县|
宁城县|
郸城县|
金平|
松溪县|
嘉黎县|
镇坪县|
无锡市|
闽侯县|
桂平市|
松潘县|
梓潼县|
博乐市|