適用范圍 Applicable scope

       CJX2系列交流接觸器（以下簡稱接觸器）適用于交流50Hz或60Hz、電壓至660V、電流至95A的電路中，供遠距離接通與分?jǐn)嚯娐芳邦l繁起動、控制交流電動機，接觸器還可組裝成積木式輔助觸頭組、空氣延時頭，機械聯鎖機構等部件，組成延時接觸器、可逆接觸器、星三角起動器并且可以和熱繼電器直接插接安裝組成電磁起動器。

       CJX2 series AC contactor (here in after referred to as contactor) for AC 50Hz or 60 Hz, the voltage to 660V, current to 95A Circuit, for remote connection and breaking circuit and frequent start, control AC motor, contactor can also be assembled into a modular auxiliary contact group, Air delay head, mechanical interlock mechanism and other components, composed of delay contactor, reversible contactor, star delta starter and can and thermal relay Directly connected to form an electromagnetic starter.

型號及其含義 Model and its meaning

主要技術參數 The main technical parameters

正常工作條件和安裝條件 Normal working conditions and installation conditions

◇周?chē)諝鉁囟葹椋?5℃~+40℃，24小時內其平均值不超過+35℃。

◇海拔：不超過2000m。

◇大氣條件：在+40℃時大氣相對濕度不超過50%，在較低溫度下可以有較高的相對濕度，最濕月的平均溫度不超過+25℃，該月的平均相對濕度不超過90%。并考慮因溫度變化發生在產品上的凝露。

◇污染等級：3級。

◇安裝類別：III類。

◇安裝條件：安裝面與垂直面傾斜度大于±50°。

◇沖擊振動：產品應安裝和使用在無顯著搖動，沖擊和振動的地方。

◇ The ambient air temperature is: -5℃ ~ +40℃, 24hours its average does not exceed +35℃.

◇ Elevation: no more than 2000 meters.

◇ Atmospheric conditions: At +40℃ when the relative humidity of not more than 50%, at a lower temperature can have a higher relative humidity, the wettest month average minimum temperature does not exceed +25℃, the average monthly maximum relative Humidity does notexceed 90%. And consider the occurrence of temperature due to condensation on the product.

◇ Pollution Level: 3 level.

◇ Installation category: III category.

◇ Installation Conditions: the installation surface and the vertical slope of more than ± 50°.

◇ Shock Vibration: The product should be installed and used where there is no significant shaking, shock and vibration.

外形及安裝尺寸 Shape and installation dimensions

訂貨須知 Ordering instructions

訂貨時必須指出：

○接觸器完整的型號名稱。

○線圈的額定工作電壓和頻率。

○訂貨臺數。

○如需訂購標準卡軌，應另行注明。

訂貨示例：CJX2-09線圈電壓220V、50Hz、10臺。

When ordering, you must point out:

○ Contactor complete model name.

○ Rated operating voltage and frequency of coil.

○ Order number.

○ If you need to order the standard rail, please specify separately.

Order example: CJX2-09 coil voltage 220V, 50Hz, 10 units.